Everyday Low Prices

We offer our very best prices upfront to Trade & DIY alike

Secure Payments

Payments Secured by Stripe

Nationwide Delivery

Fast Nationwide Delivery Available

Excellent Customer Service

See our 1400+ reviews on Trustpilot.

Secure Payments

Payments Secured by Stripe

Nationwide Delivery

Quality Products To Your Door

Rated Excellent

See our 1400+ reviews on Trustpilot

Classic Bond Rubber Roofing Contact Adhesive

Trade prices for all

Fast online ordering

Click & Collect

Nationwide Delivery

Trade prices for all

Fast online ordering

From: £17.59 Inc VAT

Free Delivery on orders over £900 (incl VAT)

Delivery: 2 - 4 Days
Delivery: 2 - 4 Days
Delivery: 2 - 4 Days
Delivery: 2 - 4 Days

Order Online

Best Prices

Classic Bond Rubber Roofing Contact Adhesive

From: £17.59 Inc VAT

Free Delivery on orders over £900 (incl VAT)

Delivery: 2 - 4 Days
Delivery: 2 - 4 Days
Delivery: 2 - 4 Days
Delivery: 2 - 4 Days

Everyday Low Prices

Our huge buying power with leading manufacturers means lower prices for you

ClassicBond Rubber Roofing Contact Adhesive – 1L, 2.5L & 5L

ClassicBond Rubber Roofing Contact Adhesive is a high-strength, solvent-based adhesive specifically formulated for bonding ClassicBond EPDM rubber roofing membrane to a wide range of compatible roof surfaces.

Fast curing and highly versatile, it is particularly suited to areas where a strong contact bond is required, including roof perimeters, angle changes, upstands, steep slopes and vertical surfaces.

The adhesive is applied to both the substrate and the underside of the EPDM membrane using a spreader brush or short-pile roller. Once both surfaces are touch dry, they are brought together to create a strong and immediate bond.

Available in 1 litre, 2.5 litre and 5 litre cans, ClassicBond Contact Adhesive can be used on compatible timber, brick, render, metal, plastic, concrete and approved insulation surfaces.

What Is ClassicBond Contact Adhesive Used For?

ClassicBond Rubber Roofing Contact Adhesive is designed for areas of an EPDM roof where Water Based Deck Adhesive is unsuitable or where a stronger contact bond is required.

Typical applications include:

  • Roof perimeters
  • Upstands
  • Vertical surfaces
  • Angle changes
  • Steep slopes
  • Non-permeable roof decks
  • Brick and rendered surfaces
  • Metal surfaces
  • Compatible plastics
  • Concrete
  • Approved insulation boards

It is particularly important around roof edges and upstands where the EPDM membrane may experience greater stresses from structural movement and changes in direction.

Features & Benefits

  • High-strength EPDM contact adhesive
  • Specifically designed for rubber roofing installations
  • Solvent-based formulation
  • Fast curing
  • Suitable for horizontal and vertical applications
  • Ideal for roof perimeters and upstands
  • Suitable for angle changes and steep slopes
  • Bonds EPDM to a wide variety of compatible materials
  • Applied using a spreader brush or short-pile roller
  • Available in 1L, 2.5L and 5L cans
  • Suitable for professional and DIY EPDM installations

Available Sizes & Coverage

ClassicBond Rubber Roofing Contact Adhesive is available in three sizes:

Size Approximate Coverage
1 Litre 1 to 2m²
2.5 Litres 4 to 5m²
5 Litres 7 to 10m²

The stated application rate is approximately 0.5 litres per m² when applied to both mating surfaces.

Actual coverage will vary depending on the porosity, texture and condition of the surfaces and the amount of adhesive applied.

Suitable Surfaces

ClassicBond Contact Adhesive can bond EPDM membrane to a wide range of compatible roofing substrates, including:

  • Timber
  • Brick
  • Render
  • Metals
  • Compatible plastics
  • Concrete
  • Approved insulation products

Always ensure that the substrate is suitable for the adhesive and EPDM roofing system before installation.

Important: Not Suitable for Expanded Polystyrene

ClassicBond Rubber Roofing Contact Adhesive must not be used with expanded polystyrene (EPS).

As a solvent-based product, it should only be used with compatible substrates and insulation materials.

Where insulation forms part of the roof construction, check that the insulation is approved for use with the adhesive before application.

Application to Upstands & Vertical Surfaces

ClassicBond Contact Adhesive is particularly suitable for bonding EPDM around upstands and vertical details.

Using a 4 inch mini roller, apply the Contact Adhesive evenly to:

  1. The upstand or substrate
  2. The corresponding underside of the EPDM membrane

Allow the adhesive on both surfaces to become touch dry before carefully bringing the membrane into contact with the substrate.

Once the surfaces make contact, roll the membrane firmly into position to create the required bond.

150mm Perimeter Bonding Strip

When installing ClassicBond EPDM, the membrane should also be secured around the appropriate roof deck perimeter using an approximately 150mm wide strip of Contact Adhesive.

This provides additional restraint around the roof edge and helps prevent the membrane from lifting as a result of structural movement.

The perimeter adhesive should be applied to both the roof deck and corresponding underside of the EPDM membrane.

Application to Non-Permeable Roof Decks

ClassicBond Contact Adhesive can be used on compatible non-permeable roof deck surfaces where the installation requires a contact bonding method.

Using a suitable roller, apply an even coat of adhesive to:

  • The roof deck
  • The underside of the EPDM membrane

Allow both adhesive-coated surfaces to become touch dry before carefully rolling the membrane onto the roof deck.

Depending on the conditions, the adhesive may typically require approximately 5 to 20 minutes to become touch dry.

Drying times will vary according to temperature, ventilation, humidity and application conditions.

Important: EPDM Cannot Be Repositioned After Contact

Contact adhesive creates a rapid bond when the two prepared surfaces meet.

Once the EPDM membrane has been brought into contact with the adhesive-coated substrate, it is not normally possible to reposition it.

Carefully align the membrane before allowing the two surfaces to make contact, particularly when working around upstands, edges and larger areas.

Contact Adhesive vs Water Based Deck Adhesive

ClassicBond Contact Adhesive and Water Based Deck Adhesive perform different roles within an EPDM roofing installation.

Contact Adhesive

Best suited to:

  • Roof perimeters
  • Upstands
  • Vertical surfaces
  • Angle changes
  • Steep slopes
  • Compatible non-permeable substrates
  • Detail areas requiring an immediate contact bond

Water Based Deck Adhesive

Typically used for:

  • Main horizontal roof areas
  • Suitable permeable timber roof decks
  • Large areas of standard fully bonded EPDM membrane

Many ClassicBond installations therefore use Water Based Adhesive across the main roof deck and Contact Adhesive around the perimeter and upstands.

Application with Brush or Roller

ClassicBond Contact Adhesive is formulated for application using a suitable:

  • Spreader brush
  • Short-pile roller
  • 4 inch mini roller for smaller areas and upstands

Apply the adhesive evenly and avoid excessive build-up.

Both mating surfaces require adhesive when using the product as a contact bond.

Commercial & Larger EPDM Roof Installations

For applicable commercial installations and projects in excess of 100m², ClassicBond specifies that the entire roof area should be bonded using the appropriate ClassicBond Bonding Adhesive system.

Large or commercial roofing projects should always follow the relevant ClassicBond specification for the particular roof construction and substrate.

High-Strength Adhesive for EPDM Details & Perimeters

ClassicBond Rubber Roofing Contact Adhesive provides the strong, fast-curing bond required around some of the most demanding areas of an EPDM flat roof.

Its ability to bond ClassicBond EPDM to a wide range of compatible substrates makes it particularly useful for roof perimeters, upstands, vertical surfaces, angle changes and non-permeable decks.

Available in 1L, 2.5L and 5L cans, with coverage of up to approximately 10m² from the largest size, it provides a versatile bonding solution for both DIY and professional ClassicBond EPDM roofing installations.

Installation Guide

Download Guide
Watch Video

Additional information

Size

, ,

Rated as Excellent on Trustpilot

Our customer service is rated as excellent on Trustpilot where we have over 1500 genuine customer reviews.

Customers also bought

Secure Online Ordering

As a family-run business, your trust really matters to us. That’s why all orders and payments are placed securely through our website, helping to keep your details safe and your order processed correctly.

We use your card issuer’s 3D Secure checks, and all payments are encrypted and handled securely by Stripe, a trusted payment provider. We never see or store your card details, so you can order with confidence knowing you’re in safe hands with Roofin Online.

Nationwide Delivery

We offer nationwide delivery on most products.

Delivery times are in working days (excluding weekends and bank holidays). Orders placed after 12 noon are processed from the next working day.

Some products and locations have delivery restrictions. Available options and costs are calculated automatically at checkout.

Click & Collect

We offer free Click & Collect on most products in our online shop.

Available collection locations are displayed automatically in your basket and at checkout, based on the products you’re ordering.

We’ll contact you when your order is ready for collection. Please wait for confirmation before travelling.

Rated as Excellent

Our customer service is rated as excellent on Trustpilot where we have over 1500 genuine customer reviews.